One Call for Plumbing, Gas and Electrical in Vernon (2026): Does It Work?
There is a specific kind of Vernon project that turns into a scheduling nightmare. A furnace replacement that needs a gas fitter and an electrician. A kitchen renovation that needs a plumber to move a sink, an electrician for the new circuits, and a gas fitter for the range. A restaurant cooler that needs refrigeration work and a dedicated circuit at the same time.
Individually, each of those trades is easy to find. Getting three of them to show up in the right order, in a town this size, is the actual problem. That is why multi-trade contractors exist, and it is worth understanding when they are the right answer and when they are not.
What each trade requires in BC, briefly
Knowing the licensing helps you ask better questions.
Electrical. Requires a licensed electrical contractor with a qualified FSR, and permits with inspection for most work beyond a fixture swap.
Gas fitting. Requires a licensed gas contractor and a certified gas fitter with the appropriate class. Gas permits and inspections apply to appliance installations, line alterations, and venting work. This is not a trade to be casual about, because the failure modes are carbon monoxide and fire.
Plumbing. Regulated through municipal plumbing permits for most alterations to the drain, waste, vent, and supply systems. Not everything needs a permit, but rough-in changes generally do.
Refrigeration. Requires refrigeration certification and, for handling refrigerants, environmental certification.
A company advertising all of these is telling you it holds several separate licences and carries certified people in each. That is a meaningful bar to clear, and it is worth confirming rather than assuming.
When one company for everything is genuinely better
When the trades have to interlock. A furnace, boiler, or hot water tank replacement usually touches gas, venting, electrical, and sometimes plumbing at once. When one company owns all of it, nobody is standing around waiting for someone else, and nobody is blaming someone else.
When you need after hours response. A no-heat call in a Vernon January, a burst line, or a walk-in cooler failing on a Saturday. A company with several trades in house can usually send someone who can actually finish the job rather than diagnose it and book a return visit.
On commercial and multi-family sites, where a property manager values one invoice, one point of contact, and one company accountable for the whole mechanical room.
When scheduling is the constraint, which in Vernon it usually is.
When separate specialists are better
Be honest about this too.
Large single trade projects. A whole home repipe, a full rewire, or a major HVAC design is a specialist project, and a dedicated specialist will usually do it faster and often cheaper.
Highly specialized equipment. Some appliances, boiler brands, and commercial systems need factory trained service. Ask directly whether they work on your specific equipment.
When you want competitive pricing on one trade. Bundling is convenient. It is not automatically cheaper on a single trade job, and you should still get a second quote on anything substantial.
The reasonable position is that multi-trade is a strong default for mixed and urgent work, and specialists are better for large single trade projects.
What to ask a multi-trade contractor in Vernon
1. Which licences do you hold, and can I have the contractor licence numbers for electrical and gas?
2. Are the trades in house or subcontracted? Both can work. What you want to know is who is accountable.
3. Who pulls the permits for each portion of the work?
4. Is your after hours service staffed by your own people, and what is the call-out charge?
5. How do you bill a job that crosses trades? One invoice with the trades itemized is the answer you want, so you can see what each portion cost.
6. What is the warranty on labour, and is it the same across all trades?
7. Do you work on my specific equipment, naming the brand and model.
Costs to expect in Vernon in 2026
Rather than a single number, know the shape of the pricing:
- Diagnostic or service call fee. Most companies charge to come out, sometimes credited toward the repair. Ask up front, and ask separately about after hours.
- Hourly labour rates differ by trade, and refrigeration and gas typically sit above general plumbing.
- Emergency and statutory holiday premiums are normal and can be substantial. If your problem can safely wait until Monday, ask what that saves.
- Equipment replacement is where the large numbers live. A water heater replacement, a furnace replacement, or a commercial refrigeration compressor are each a defined project and should be quoted, not billed hourly.
For any equipment replacement, ask for the model number of what is being installed, the warranty on the equipment, the separate warranty on labour, and whether permits and inspection are included.
The emergency question, answered before the emergency
The most valuable thing you can do is decide who you would call before you need them. A no-heat night or a leak at 11 p.m. is the wrong moment to compare companies.
Pick one, put the number in your phone, and ask them now:
- What hours do you actually answer?
- What is the after hours call-out charge?
- Do you service my area, and how far out is Vernon versus Coldstream, Lumby, or Armstrong?
- What should I do before you arrive? Knowing where your main water shutoff and your gas shutoff are, and how to use them, is genuinely the most useful five minutes you will spend.
Frequently asked questions
Is a multi-trade contractor more expensive?
Not inherently. On mixed jobs it is frequently cheaper because you are paying for one mobilization rather than three, and because nobody is waiting on anybody. On single trade jobs, compare quotes as you would with anyone.
Do they handle both residential and commercial?
Many do, and commercial capability is often a good sign of depth, since commercial work carries stricter requirements. Ask about experience with your building type.
What about septic and well systems?
Rural properties around Vernon frequently need pump, septic, and line work alongside plumbing. Ask whether the company covers it, because not every plumbing contractor does.
How quickly can they come out?
Ask for both a normal lead time and an emergency response commitment, and hold them to the one they give you.
A Vernon option
*Disclosure: Aslan Electrical, Plumbing, Gasfitting, Refrigeration and Sheetmetal Services Ltd is a business listed on the Okanagan Trade Directory. The details below come from their own published information and their public Google profile as of writing.*
Aslan Electrical, Plumbing, Gas Fitting, Refrigeration and Sheet Metal Services Ltd. is a Vernon trades company serving residential, commercial, and industrial clients, operating since 1983. They cover a broad mix of trades under one roof: electrical wiring installation and repairs, residential and commercial plumbing, gas fitting for appliances such as dryers, ranges and furnaces, refrigeration, sheet metal, and heating repair and service. Additional work includes water heater repair and installation, septic tank and pump service, sewer camera inspection, line locating, and repair of restaurant and bakery equipment. The company states it is bonded, licensed, and insured, and offers 24 hour emergency response including weekends and after hours on weekdays. It holds a 5.0 star rating across 138 Google reviews.
See their Okanagan Trade Directory listing or visit aslanservicesltd.com.
Whether you go with one company or three, ask for the permit numbers. Across every one of these trades, that is the shortest route to knowing the work was inspected.